Dongbu Steel Co., Ltd. (016385) Plunges -2.94% on Jan 10 | Spiral Carbon Steel Pipe

24 – Celine Dion announced on social media that she would leave her Caesars Palace residency in June 2019.

All loading, cutting, and unloading operations are controlled by CNC, and the system control software automatically selects the best cutting method. Because all machine operations are performed by programmed commands, no manual setups or fixtures are required. Once tubes are placed on the loader, they are moved one by one into the feeding line with its automated chuck system.

The pre-market morning session on the SET starts at 9:30 a.m., and ends anytime between 9:55 a.m. and 10:00 a.m. The regular morning session starts anytime between 9:55 a.m. and 10:00 a.m., and ends at 12:30 p.m. Meanwhile, the pre-market afternoon session starts at 2:00 p.m., and ends anytime between 2:25 p.m. and 2:30 p.m. The regular afternoon session starts anytime between 2:25 p.m. and 2:30 p.m., and ends at 4:30 p.m. Lastly, the post-market session starts at 4:30 p.m., and ends anytime between 5:00 p.m. and 5:10 p.m.

Each process-development program requires several project phases, from the initial proof-of-concept through numerous levels of technical readiness, stage gates and eventually to the construction of the commercial plant. These reassessment requirements vary greatly from company to company. As one can imagine, the technical readiness requirements for a major petroleum or chemical company are likely different from those of a technology licensor or engineering company. Even within the same organization, depending on starting point and complexity, each technology-development program has its own path and strategy to get from the initial concept to full-blown commercialization. Additionally, risk mitigation and individual risk tolerances set and drive the scaleup progression and development lifecycle. The textbook rules of process scaleup include steps going from a very small-scale testing apparatus (bench scale) to a more representative pilot plant, then possibly to a demonstration unit and finally to the commercial plant (Figure 2). It should be highlighted that scaleup is not only limited to the key process-unit operations, but also to the catalysts, feedstocks, additives and equipment that form the complete basis for the new process.

We should also talk a bit more about the Defiance wireless signal system. The Defiance WT Wireless Module is sold separately and does away with the need for a physical wire for the signal. Omitting the signal cable can greatly increase the availability of potential placements for the sub, and since the placement of the subwoofer is so critical in getting good sound, this can be a very significant assist in sound quality. The Defiance WT Wireless System uses 2.4 GHz dynamic frequency selection and error correction. The receiver end of the Defiance WT system is powered by the subwoofer itself and so does not need to be plugged into a power outlet. The Defiance WT Wireless Subwoofer System has a 50-foot range, so it should be able to handle any conventional domestic room size without a problem.

8 – Statistics Canada’s controversial plan to harvest personal financial data without people’s consent was put on hold pending the completion of an investigation of the legality and intrusiveness of the project. The federal agency caught nine financial institutions off guard by informing them they were required to provide banking information on Canadians in 500,000 households across the country.

The reversal of the decision to shut down Hydro’s Alunorte refinery means alumina prices will quickly break below the $500 per tonne level, traders said.

One of the most important goals of reactor design is to replicate the mass- and heat-transfer characteristics, fluid linear velocities, flow regimes (turbulent versus laminar) or Reynolds numbers used during piloting. CFD modeling of reactor systems is a powerful tool to predict and optimize flow distribution, heat transfer and mixing (Figure 7). For irregular reactor geometries, CFD can provide a reasonable estimate of pressure drop and flow patterns. CFD can highlight problem areas, such as unwanted backmixing, stagnant areas and elements that may be prone to vibration. CFD is particularly helpful in developing reactor details, such as feed injections and mixing elements, which are very difficult to translate directly from the pilot scale.

30 – The Saskatchewan government introduced its own climate change legislation as its feud with Ottawa over a carbon tax continued to play out in the courts. The bill laid the groundwork for standards to reduce industrial greenhouse gas emissions.

To subscribe email subscriptions@creamermedia.co.za or click here To advertise email advertising@creamermedia.co.za or click here

“Another consideration was the state of the market. Fiber-optic tube and section lasers are relatively new to the South African market so it made sense to invest in unique technology.”

25 – Pope Francis acknowledged that the sex abuse scandals rocking the Catholic Church had outraged the faithful and said the church must change its ways if it wanted to keep future generations. The statement followed the release of a report that concluded at least 3,677 people were abused by clergy between 1946 and 2014.